Technical Data
| Standard | IEN61008-1 IEN62423 |
| Type | Electronic type (Auxiliary Electromagnetic type) |
| Characteristics of residual operation current | and B |
| Poles | 1P+N,3P+N |
| Rated operating break capability | 10 InA |
| Rated current (A) | 25,40,63 |
| Rated voltage | AC 240/415 |
| Rated frequency | 50/60 HZ |
| Rated residual operation current I△n (A) | 0.03, 0.1 and 0.3 |
| Rated residual non-operating current I△nno | 0.5I△n |
| Rated limited short circuit current | 10 KA |
| Rated limited residual short circuit current l△c | 10 kA |
| Scope of residual operating current | 0.51△n~I△n |
| Wiring height | 19 mm |
| Mechanical electrical life | 4,000 cycles |
| Wiring section area of terminal | conductor of 25 mm² and below |
| Wiring terminal | screw terminal |
| Wiring method | column type wiring method |
| Tightening torque | 2.0Nm |
| Installation | Installation of 35.5mm guide rail / Vertical installation |
| Enclosure protection class | IP20 |
Basic parameters
| Rated current of housing grade Inm(A) | Poles | Frequency (Hz) | Rated voltage Ue(V) | Rated current In(A) | Rated residual current(A) | Rated limited short circuit current Inc(A) | Rated limited residual short circuit current I△C(A) |
| 63 | 1P+N | 50/60Hz | 240 | 25 40 63 | 0.03 0.1 0.3 | 10000 | 10000 |
| 3P+N | 415 |
| Type | In(A) | I△n(A) | Standard value of breaking time and non-operating time for equality of residual current (I△A ) and following values (S) | |||
| 2 I△n | 4 I△n | 10 I△n | 5A,10A,20A,50A,100A,200A | |||
| General type | Any value | Any value | 0.3 | 0.15 | 0.04 | 0.04 |
| Model | Tripping current I△ /A | ||
| AC | 0.5 I△n＜I△n | ||
| A | Angle of retard | I△n>0.01A | I△n＜0.01A |
| 0° | 0.35I△n≤I△≤1.4I△n | 0.35I△n≤I△≤2I△n | |
| 90° | 0.25I△n≤I△≤1.4I△n | 0.25I△n≤I△≤2I△n | |
| 135° | 0.1I△n≤I△≤1.4I△n | 0.1I△n≤I△≤2I△n | |
| Frequency(Hz) | Residual non-operating current | Residual operating current |
| 150 | 0.5I△n | 2.4I△n |
| 400 | 0.5I△n | 6I△n |
| 1000 | I△n | 14I△n |
- For sinusoidal AC residual current no more than 1000Hz, the trip current range between diferent frequencies according to the requirements of Table 2.With a sudden residual trip current in Table 2, the breaking time should be no more than 0.3s,The minimum no trip time of type S should be no less than 0.13s, and the maximum breaking time should not exceed 0.5s.
- lf smooth residual current 0.4 time rated residual operation current (I△n) or 10 mA smooth DC residual current (the bigger shall prevail) is overlapoed on the rated frequency AC residual current. type B RCCB shall be operated. and the AC trippind current shall be no more than l△n.
- If smooth DC residua current 0.4 tme rated residual operation current (I△n) or 10 mA smooth DC residua current (the biocer shaprevai) is overlapped on the pulse DC residual current. type B RCCB shall be operated. The tripping current of RCCB with l△n > 0.01A shall be no more than 1.4 l△n while the tripping current of RCCB with l△n≤0.01 A shall be no more than 2l△n.
- For the pulse DC residual current which is stably increased and produced by two relative rectifying circuits, type B RCCB shall be actuated within the scope of 0.5 l△n to 22 1△n Type B shall trip within the time range specified according to the Table 1,With a sudden pulsating DC residual current applied to the rectifier circuit.
- For the pulse DC residual current which is stably increased and produced by three relative rectifying circuits, type B RCCB shall be operated within the scope of 0.5 l△n to 22 1△n Type B shall trip within the time range specifed according to the Table 1,With a sudden pulsating DC residual current applied to the rectifier circuit.
- For the smooth DC residual current which is stably increased, type B RCCB shall be operated within the scope of 0.5 l△n to 22 1△n Type B shall trip within the time range specifed according to the Table 1.With a smooth DC residual current applied to the rectifier circuit.
- According to the Table 3, composit wave and initial value provided in steady.RCCB composite wave residual current range of 0.5I△n to 1.4 1△n, Sudden application of 71△n,Normally the RCCB break time should be less than 0.04s, Type S RCCB break time should be less than 0.15s.
| The component values of different frequencies in the test current (RMS) | The verified correct initial value (RMS) | ||
| Rated Frequency | I 1kHz | I FMotor (10Hz) | I △ |
| 0.138I△n | 0.138I△n | 0.035I△n | 0.2I△n |
